<progress id="5x7nt"></progress>
<rp id="5x7nt"></rp>

    <listing id="5x7nt"></listing>

        <p id="5x7nt"></p>
        
        

        <big id="5x7nt"></big>

          <thead id="5x7nt"></thead>

          咨詢熱線
          當前位置: 首頁 > 新聞中心 > 公司動態 >

          卷簾門鑰匙轉不動、拔不出來怎么辦?

          發布人:http://www.bj-dcpj.com    發布時間:2021-03-02 13:48:35

          卷簾門的機械鎖是目前門類產品中使用頻率最低的產品,沒有之一,由于長時間不使用會導致鎖具生銹、卡頓等現象的出現,導致卷簾門的鑰匙插不進去、轉不動、拔不出來等種種問題,那么,一旦遇到這種現象如何解決呢?
          At present, the mechanical lock of rolling shutter door is the product with the lowest frequency of use in the door products, and it is not one of the products. Because it is not used for a long time, it will lead to the appearance of the lock rust, stuck and other phenomena, resulting in the rolling shutter door key can not be inserted, turned, pulled out and other problems. Then, once this phenomenon is encountered, how to solve it?
          首先要分析卷簾門機械鎖故障的原因,仔細觀察,才能找到有效的解決方案。我們可以逐一分析。
          First of all, it is necessary to analyze the causes of the failure of the mechanical lock of the rolling shutter door, and carefully observe it, in order to find an effective solution. We can analyze them one by one.
          1·鎖芯內有泥土等故障:由于卷簾門的鎖芯在底部,距離地面很近,平時的走路、風吹、雨淋等都有可能導致灰塵泥土進入鎖芯,此時如果發現鎖芯內有泥土,先不要著急插鑰匙,用別針、牙簽等工具清理鎖芯內的泥土,然后用易揮發的潤滑油潤滑,干燥后用固體潤滑劑石墨進行潤滑,一定要定期檢查清理雜物。
          1. There are soil and other faults in the lock cylinder: because the lock cylinder of the rolling shutter door is at the bottom and very close to the ground, usually walking, wind blowing, rain and so on may cause dust and soil to enter the lock cylinder. At this time, if there is soil in the lock cylinder, do not rush to insert the key, use pins, toothpicks and other tools to clean the soil in the lock cylinder, and then use volatile lubricating oil to lubricate, and use solid lubricant after drying Lubricant graphite lubrication, be sure to regularly check and clean up debris.
          濟南卷簾門
          濟南卷簾門
          Jinan rolling shutter door
          2·鎖芯內有異物:鎖芯內有異物80%以上都是惡作劇或者故意報復,人為的將竹簽、膠水等灌注到鎖芯內,這種情況鑰匙一般插不進去,如果是牙簽、竹簽等異物,可以嘗試用別針摳出來,如果扣不出來就只能暴力換鎖了,如果是膠水灌注,則必須換鎖了。
          2. There are foreign matters in the lock cylinder: more than 80% of the foreign matters in the lock cylinder are pranks or deliberate retaliation, and the bamboo stick and glue are artificially poured into the lock cylinder. In this case, the key can not be inserted. If it is toothpick, bamboo stick and other foreign matters, you can try to pick them out with a pin. If you can't buckle them out, you can only change the lock violently. If it is glue pouring, you must change the lock.
          3·長時間不使用導致鎖具生銹:這種是最常見的一種現象,首先潤滑是必須的,而且使用固體潤滑劑,用小孩的鉛筆筆芯粉末,撒到鑰匙上,插入鎖芯后反復旋轉,讓石墨粉均勻分布就可以了,此時就會感覺到鑰匙進出都非常順暢。
          3. Long time disuse leads to lock rusting: This is the most common phenomenon. First of all, lubrication is necessary, and solid lubricant is used. Use children's pencil lead powder, sprinkle it on the key, insert it into the lock core and rotate it repeatedly, so that the graphite powder is evenly distributed. At this time, you will feel that the key is very smooth in and out.
          如果是鑰匙已經插進去了,轉不動,拔不出來,此時就要詳細回憶插入鑰匙都做了哪些動作,一般這種現象都是鑰匙插反、查的不到位等原因,在輕度旋鈕鑰匙后,鑰匙孔抱死,鑰匙動不了了,此時只要按照原來動作的相反動作操作,也就是讓鑰匙復位到剛插入的狀態,調整鑰匙深淺或者加入潤滑劑。
          If the key has been inserted, can't turn, can't pull out, at this time we have to recall in detail what actions have been done to insert the key. Generally, this phenomenon is caused by the key inserted reversely, the check is not in place and so on. After slightly turning the key, the key hole is locked, and the key can't move. At this time, we just need to operate according to the opposite action of the original action, that is, to reset the key to the just inserted position Adjust the key depth or add lubricant.
          此時,鑰匙就可以正常使用了。但是,這僅僅是低級錯誤;很多時候往往都是這樣的動作,鑰匙沒有完全插入,擰半圈擰不動,發現鑰匙沒有插入到位,直接繼續插入,繼續擰鑰匙就卡死了;又或者插入鑰匙擰了半圈擰不動,準備拔出來,拔了一點點拔不動,繼續擰,鑰匙卡死了。
          At this time, the key can be used normally. However, this is only a low-level error; most of the time, it's like this: if the key is not fully inserted and can't be turned by half a turn, if you find that the key is not inserted in place, you can continue to insert it and continue to turn the key, and then it's stuck; or if you insert the key and can't turn it by half a turn, you're ready to pull it out.
          上一篇:卷簾門開門時怎么發生感應的你知道嗎?
          下一篇:看完這些你還敢說你了解濟南卷簾門嗎?
          產品中心
          聯系我們